![\"Expanding](\"http:\/\/www.smallnetbuilder.com\/images\/stories\/basics\/how_to_add_ports\/router_and_switch.jpg\" "\\"Expanding")
<\/p>\nI often see questions in the forums from people struggling with one of the most basic tasks in creating a home network: what to do when you run out of ports in your router.<\/p>\n
The answer is to just connect a switch, as shown in the diagram below.<\/p>\n
<\/p>\n
But since that makes for a very short article, I’ll answer some questions about adding a switch that I’ve often seen.<\/p>\n
No. The simple explanation is that (consumer) routers can share a single Internet connection among multiple computers<\/a>. Switches cannot. Switches allow you to share a single port on your router (or another switch) among multiple Ethernet devices.<\/p>\n Switches handle data based on the MAC address<\/a> in the data packet. The switch automatically learns the MAC address of each device connected to its ports and stores it in a lookup table in the switch.<\/p>\n Each data packet sent contains the source MAC address from the device sending the data and a destination MAC address for the device that the data is intended for. The switch looks at the destination address and sends the data only to the physical switch port that the destination device is connected to.<\/p>\n No. The only time data leaves the switch is when the data packet contains a destination address for a device that is not connected to the switch.<\/p>\n So if you have a network media player playing a file stored on a NAS that are both connected to the same switch as shown below, data never touches the cable connecting the switch to a router.<\/p>\n Maybe. The single connection between the switch and a router can become a bottleneck if the total amount of data simultaneously<\/em> sent across the connection exceeds the capacity of the connection. A 10\/100 switch can handle 100 Mbps total of data in each direction<\/em> simultaneously on each port; a Gigabit (10\/100\/1000) switch can handle 1000 Mbps.<\/p>\n Bottlenecking usually doesn’t happen for web browsing, email and similar activities in home and small business networks<\/a> because the data sizes are relatively small, the activity is intermittent and the number of devices is low.<\/p>\n What can<\/em> cause problems are sustained activities like large file transfers, Torrenting and multiple video streams.<\/p>\n The only way to make sure that you don’t run into a bottleneck is to analyze your data flows and keep flows with high bandwidth requirements on the same switch. If you want to actually measure network speed, see How Fast Is Your Network? Five Ways To Measure Network Speed<\/a>.<\/p>\n All of today’s switches (10\/100 and Gigabit) are designed to provide non-blocking wire-speed transfer between all switch ports simultaneously. This means each pair of devices can send and receive data at their maximum port speed, without interfering with any other pair.<\/p>\n Also see #14 below.<\/p>\n No. But in the old days, it did. Switch ports were designed to primarily connect to devices. So when you had to add a switch you had to either use a special crossover cable that swapped the receive and transmit wire pairs. Or sometimes routers<\/a> and \/ or switches would have special “uplink” ports that had the receive and transmit connections already swapped.<\/p>\n All that has gone away. All of today’s routers and switches have ports with auto MDIX<\/a>, which automatically detects whether a device or another switch port is connected and adjusts accordingly.<\/p>\n Even if you have a very old router, the switch you purchase will have auto MDIX and all you need is one device that supports it (but it’s ok if both switch and router do).<\/p>\n Sure. But keep in mind the bottlenecking issue in #4 and group your devices and size your switches to avoid it.<\/p>\n If you do add multiple switches, use a star connection (see below) when possible and avoid daisy-chaining switches.<\/p>\n Managed and “smart” switches won’t buy you any more performance. They do provide special features that can come in handy in larger networks. See Smart Switch How To – Part 1: What A Managed Switch Can Do For Your Small Network<\/a> to help you decide.<\/p>\n Yep. See How To Use a Router To Add Network Ports<\/a>. Use Method 1 to avoid unnecessary hassle.<\/p>\n No. The ports on the router connect to a switch chip, which works the same way as a chip in a standalone switch. The “routing” part of the router, i.e. the part that handles data to and from the Internet doesn’t get involved with data moving between<\/em> devices on the switch.<\/p>\n 100 Meters, the same as between a device and the switch.<\/p>\n Today’s switches have everything integrated into a chip. The inside of the D-Link DGS-2208 shown below clearly shows the Vitesse switch chip. The rest of the components are for power supply and required to support the switch chip.<\/p>\n2. How does a switch work?<\/h3>\n
3. Does adding a switch to my router slow it down?<\/h3>\n
![\"Local](\"http:\/\/www.smallnetbuilder.com\/images\/stories\/basics\/how_to_add_ports\/local_data_flow.jpg\" "\\"Local")
<\/p>\n4. Will putting devices on an added switch slow them down?<\/h3>\n
5. Does it matter which ports I use to connect?<\/h3>\n
6. Can I add more than one switch?<\/h3>\n
<\/p>\n
9. Can I reuse an old router as a switch?<\/h3>\n
10. Does it matter whether I use ports on the router or ports on the added switch?<\/h3>\n
11. How long can cables between switches be?<\/h3>\n
12. What does the inside of a switch look like?<\/h3>\n
![\"Inside](\"http:\/\/www.smallnetbuilder.com\/cache\/multithumb_thumbs\/b_551_0_16777215_0___images_stories_lansrouters_8port_gigabit_roundup_dlink_dgs_2208_board.jpg\" "\\"Inside")
<\/a><\/p>\n